Pro-Tech Straight Bit 1′(25.4mm) X 1 1/4′(31.8mm) Two Flute 1/2′ Shank

Pro-Tech Router Bits & Saw Blades South Africa

Pro-Tech Straight Bit 1′(25.4mm) X 1 1/4′(31.8mm) Two Flute 1/2′ Shank

R299.00 Incl. VAT

9 available. Delivery 3-6 working days. Learn more.

Or split into 4x interest-free payments Learn more
Purchase this product now and earn 30 Bench Marks!

Add to Quote
SKU: KP210L Category:

Description

Pro-Tech. South African favourite for over 30 YearsDouble
flute Straight bit

Two Flute Straight bit KP210L by Pro-TechIn
choosing a straight bit for any application, always select one with the shortest
cutting edges and the shortest overall length that will reach the required cut depth.
Excessive length intensifies deflection and vibration, which degrade cut quality
and lead to tool breakage.

Use
a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating
vibration that degrades the cut finish.

Two cuts per revolution yield a smooth surface,
but feed rate is slightly reduced.

This router bit has a
12.7mm shank (shaft) that will fit most large routers. Please
ensure that you select a router bit with a shank (shaft) size that will fit
into your router collet.

 

PRO-TECH
router bits are manufactured in Taiwan.

safety

consider
safety for your health and the people around you

General safety suggestions:

It is advisable to always have the following items nearby and in a good
condition

  • Eye protection – clean and scratch free
  • Hearing protection – quality earmuffs
  • Dust masks – discard old and dirty masks
  • Gloves – for easy handling of material and hand protection
Wear GlovesEye ProtectionHearing ProtectionDust Mask
Wear Gloves
Eye Protection
Hearing Protection
Dust Mask

To use router bits safely (and to get the best results from your router), the
router bits need to be installed properly into the router’s collet. Improper installation
of your bits can cause excessive chatter and could increase the likelihood that
the bits will break when in use.

Clean and sharp

First of all, before beginning any routing operation, check your bits to
make sure that they are clean, relatively free of pitch, and most of all, sharp.
If the bit is dull, chipped, is excessively burned or has any other defect,
it should be sharpened or replaced before use.

Correct
collet and collet nut fit

Most router collets have a recess (groove) that needs to click into a circlip
that resides inside the collet nut. Failing to ensure that the collet ‘clicked’
into the collet nut will cause you to struggle to remove the router bit after
tightening. This could cause the collet to break or be removed by a technical
repair centre.

 

Correct
fit inside the collet

When installing the bit into the collet, do not tighten the collet with the bit
‘seated.’ Instead, insert the bit until the shank (bit shaft) reaches
the bottom of the collet, then ease it out about 2 mm before tightening the collet.

When the bit is tightened, there should be no less than  2/3
‘s of the length of the shank in the collet. If your bit has a shank that is too
short, then the bit should be replaced.

 

Safety gear

There are a few other safety measures to keep in mind whenever you use your router.
First of all, remember to always wear appropriate safety gear as indicated above.

Correct speed setting

Second, be sure to set your router to the proper speed for your router bit.
Setting your router to an incorrect speed will not only affect the router’s performance,
but also can cause the bit to break much more easily and even cause bodily harm.
The speed at which a router bit turns can be important. The typical router runs
at about 22,000 rpm, which is fine for most bits. But as the diameter of the bit
increases, you’ll want to slow things down.

Also, before beginning any routing operation, be certain that you give the router’s
motor time to come up to full speed for the chosen setting. Beginning to cut before
the bit is at full speed can give less than desired results.


Speed Settings

specifications

Part no.Shank dia.Cutting widthCutting HeightRadius (r)
KP210L1/2 in (12.7 mm)25.40 mm (1 in )32 mmStraight

 

Length of Shank: 38 mm

Straight bit, 2 Flute, TCT - 25.4 mm cutting widthCutting sample

 

Take CareFull Speed

 

Additional information

Supplier

Vermont Sales

Shank Diameter

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Pre-Sale Questions

There are no questions yet.

Ask a question about “Pro-Tech Straight Bit 1′(25.4mm) X 1 1/4′(31.8mm) Two Flute 1/2′ Shank”

Works well with

Suggest more products