DIY Bali server or console table

Avatar of Tanya Schutte

Posted by Tanya Schutte in Project Plans

For those of you who haven’t yet subscribed to Easy DIY magazine, or perhaps your local Builders Warehouse is always sold out of copies, here is the Bali Server that we made earlier this year.

We make a lot of furniture as part of our DIY Divas workshops and I often come across ideas that I would love to have in my home, but the price tag that comes with these finds is normally so exorbitant that it makes me so glad I can do-it-myself!

We’ve used pine for this project, which would normally be made of some or other exotic wood species. However, it’s a more eco-friendly option as pine is a faster growing, more prolific wood than most other. It’s also a lot more cost effective and very versatile.

You will need:

TOOLS:

CUTTING LIST:

  • A. 2 of 380 x 120mm pine – top
  • B. 4 of   44 x 44 x 800mm pine – legs
  • C. 2 of   20 x 250mm – side cross beams
  • D. 2 of   20 x 830mm – front/back cross beams
  • E. 1 of 330 x 830mm – drawer support shelf
  • 2 of 250 x 250mm – side panels
  • 2 of 44 x 44 x 200mm – upright supports
  • 6 of 10 x 10 x 300mm – drawer guides

DRAWERS:

  • 3 of 200 x 250mm – drawer fronts
  • 6 of 150 x 300mm – drawer sides*
  • 3 of 150 x 200mm – drawer back*
  • 3 of 200 x 284mm – drawer bottom*

* I used 16mm SupaWood that was lying around but you can substitute with pine.

Here’s how:

1. BUILD THE FRAME
Use the diagram below to assemble the various sections of the frame. All sections are glued and screwed from the outside. Pine is fairly soft, so drive the screws so that all screw heads are below the surface of the wood.


2. FINISH THE FRAME
Insert the shelf support [E] and attach by driving screws through the outside of the legs. Again, drive the screws below the surface of the wood.


3. MAKE THE DRAWERS
Place the drawer sides, back and front around the drawer bottom. Glue these in place and clamp until the glue has set.


4. FIT THE DRAWERS
A thin strip of SupaWood, glued to the top of the bottom drawer shelf on either side of the drawer, ensures that the drawers slide in and out easily.

Fill the gap between the drawers with the upright spacers and glue this to the top of the drawer support shelf.


5. GLUE AND FIT SIDE PANELS AND TOP
Apply glue to the edges of the side panels and place these between the front and back legs before attaching the top.

The top consists of 2 boards [A] that are glued together and clamped until the glue has set.

To ensure a seamless finish on the top, apply a small amount of wood filler mixed with wood glue to fill the gap between the two.

Once set, fit the top in place by gluing and screwing through the top into the legs and upright spacers, making sure that screw heads are below the surface of the wood.


6. AGEING THE WOOD
You want to achieve a rough, worn look around all the edges.

Start off by removing the sharp corner edges and then move the Dremel MultiTool backwards and forwards until you are happy with the desired effect.

Finish off the edges by sanding with 220-grit sandpaper until slightly smooth.


7. BURNING THE WOOD
To give the console an aged effect I first used my Dremel VersaTip soldering iron – with the soldering tip removed – to burn the edges.

It looks awful at first, but once the stain and sealer are applied it looks authentic.

 


8. FINISHING OFF
Use a clean cloth to apply Imbuia gel stain across all surfaces, adding a small amount of Ebony to a second cloth to apply small amount here and there. Blend the two stains together for an even finish. Apply 3 coats of Woodoc 5 or 10 Interior sealer, sanding with steel wool after the first coat.

If you prefer a natural finish for your Bali console Table, miss out the wood burning and staining. Roughen the edges with the Dremel MultiTool and sanding ring, sand smooth with 220-grit sandpaper and then apply Woodoc 5 Matt or Antique Wax to the surface.


Comments

Add comment